5.1 Bare board inspection (IPC-a-600)

The bare Printed Circuit Board (PCB) is not merely a passive component; it serves as the critical mechanical and electrical chassis for the entire system. If this foundation is compromised, even the highest-quality robotic soldering later cannot ensure a reliable product. We adhere to IPC-A-600 (Acceptability of Printed Boards) to clearly define the boundary between a functional, safe substrate and an unacceptable piece of fiberglass. Incoming Quality Control (IQC) must rigorously evaluate the bare board as a complex, engineered assembly rather than treating it like simple raw material.

Class selection criteria

It is crucial to define the rules of engagement before any inspection begins.

• Class 2 (Dedicated Service): Typical for standard business machines and instruments. This is our default standard expectation for General Electronics.
• Class 3 (High Reliability): Required for critical systems like life support, aerospace, or advanced automotive applications where failure is simply not an option.
• Operating Rule: If the engineering drawing does not explicitly specify a class in the notes, default heavily to Class 2 criteria.

Base material (laminate integrity)

The FR4 (or equivalent) laminate provides essential dielectric isolation and critical structural support. Failures here reliably lead to electrical shorts under thermal stress during assembly, or worse, out in the field.

Defect Taxonomy Guidelines:

• Measling: These are discrete white spots indicating resin separation from the woven glass fibers inside the board.
  • Class Decision: If the measling bridges two adjacent active conductors, Reject the board (High risk of electrical arcing).
  • Class Decision: If the measling is completely isolated, it is generally Acceptable (Considered a cosmetic defect only).
• Delamination/Blistering: A large-scale mechanical separation between the internal copper layers of the board.
  • Class Decision: If the delamination exceeds 25% of the distance between adjacent vias or conductors, Reject.
  • Class Decision: If a blister abuts a plated through-hole, Reject. (The intense, sudden heat from wave soldering will rapidly expand the trapped gas and structurally rupture the copper barrel).
• Bow and Twist: Absolute flatness is a critical physical requirement for successful Surface Mount Technology (SMT) placement.
  • Standard: Maximum 0.75% bow/twist permitted for SMT boards. (For example, a 100mm board cannot deviate from perfectly flat by more than 0.75mm).

Plating & solder mask

These protective layers shield the copper traces from oxidation and ensure robust, controlled solderability on the line.

Inspection Logic:

• Hole Breakout: Occurs when the mechanical drill slightly misses the exact center of the copper pad.
  • Class 2: Acceptable if up to a 90° breakout occurs, provided the conductive hole itself is not “open” to the outer edge of the PCB.
  • Class 3: Reject. The drilled hole must securely remain fully contained within the copper pad (“Tangency” is the maximum allowable limit).
• Solder Mask Skip:
  • Class Decision: If the green solder mask is completely missing between two fine-pitch IC pads (missing webbing), Reject. (This presents an unacceptably high risk of solder bridging during the SMT reflow process).
• Hole Wall Voiding:
  • Class Decision: If analyzing a cross-section reveals > 1 void per hole, or a void exceeding 5% of the total barrel length, Reject. (This indicates poor supplier plating and a high risk of open circuits under thermal stress).

Pro-Tip: We highly recommend performing the “Tape Test” (IPC-TM-650 2.4.1) on at least one sample board per incoming lot. Firmly apply 3M 600 tape directly to the silkscreen ink and remove it quickly. If the ink lifts off onto the tape, the supplier’s lot has a curing defect and will likely cause frustrating issues downstream.

Final Checkout: Bare board inspection (IPC-a-600)

Control Point	Guiding Principle
Flatness	Verify < 0.75% Bow/Twist. Warped boards will jam the Pick & Place machines.
Solderability	Pads must be clean, bright, and silver/gold. Visible oxidation or chemical stains = Reject the entire lot.
Annular Ring	Remember Class 2 allows 90° Breakout, while Class 3 demands 0° Breakout (Tangency is the absolute limit).
Solder Mask	Ensure there is no mask encroachment onto the pads. Mask resting on a pad = Guaranteed soldering defect.
Gold Fingers	Expect a Hard Gold finish with a smooth surface. Scratches or deep Pits on the insertion fingers = Reject.