3.3 EMI/EMC Management
Grounding,Electromagnetic shielding,behavior inside an enclosure is dictated less by circuit intent than by the physical layout of metals and cablecables. segregation.
Currents EMIfollow (electromagneticgeometry, interference)not schematics, and the wrong return path can turn a neat harness into an antenna. Effective EMI/EMC (electromagneticcontrol compatibility)comes arefrom lessdeliberate aboutgrounding mysteryschemes, robust shield terminations, and moredisciplined aboutsegregation geometry:of where currents travel, how they return,noisy and whatsensitive thezones. metalwork lets them do. A quiet box starts by choosing a ground scheme that makes sense, then bonding lids, trays, and studs so the chassis becomes the obvious return path—not the wiring harness. Shields only earn their keep when they’re terminated properly (ideally 360° at the entry), while cable segregation and tight pairing keep loops small so wires stop acting like antennas. These choices belong in assembly flow as much as in design, becauseWhen clamps, gaskets, and routing are whattreated turnas functional components rather than afterthoughts, assemblies leave the intentline intoalready physicsstable, onreducing the floor. With a couple of fast checks—a low-ohm bond read and a quick sniffneed for hotlate spots—thefixes buildor leavescostly thecompliance bench already calm.surprises.
3.3.1 The goal (in one line)
Keep noise in the noisy places and out of the quiet ones—by giving currents short, obvious return paths and making cables poor antennas.
3.3.2 Know your players: sources vs victims
Noisy stuff (emitters): switching PSUs, motor/solenoid drivers, DC–DCs, relays, PWM lines, long unshielded harnesses, poor shield bonds.
Sensitive stuff (susceptors): radios/GNSS, analog sensors, high-impedance nodes, USB/Ethernet PHYs, high-speed clocks, long signal runs.
First rule: shorten loop area (route out and back together) and give noisy currents a nearby chassis to hug.
3.3.3 Grounding strategy (decide once, build to it)
- Chassis vs 0V: treat chassis/earth as the EMC sink; treat 0V as the circuit reference. Bond them deliberately, where designed.
- Single-point (low-freq analog): tie 0V↔chassis at one slot (star) to avoid hum loops.
- Multi-point (RF/fast edges): use short, wide bonds at several points to lower HF impedance.
- Equipotential bonding: all metalwork (lids, frames, trays) must read < 0.1 Ω to chassis at their bond pads (log at first article).
- Earth joints: serrated/star washer on bare metal (23.1/23.2), torque per map, measure < 0.1 Ω.
Rule of thumb: if the problem is low-frequency ground loop (mains ripple), think single-point. If it’s RF spray, think multi-point/short bonds.
3.3.4 Cable shields & terminations (where the magic happens)
- 360° termination at entry: clamp braid/foil to chassis as the cable enters the box (backshell, gland, or clamp). Avoid pigtails; if unavoidable, keep ≤ 10 mm.
- Drain wires: bond alongside the 360° clamp, not to a distant PCB pad.
- Which end(s) to bond?
- HF noise / radiated control: both ends (360°) to kill common-mode.
- Low-freq instrumentation (e.g., 4–20 mA): single-end at the quiet end to avoid DC loops—but still add a high-frequency path (capacitor/RC or 360° with DC-isolation hardware) if the spec allows.
- Coax: treat the shield as signal return; bond shells properly (U.FL click, SMA torque).
- EMI gaskets: ensure clean bond lands; target 20–30% compression; verify seam < 0.1 Ω (23.4/23.5).
3.3.5 Segregation & routing (turn geometry into a filter)
- Zoning inside the box:
- Noisy zone (PSUs, motors, relays).
- Digital zone (processors, high-speed).
- Quiet/analog/RF zone (sensors, radios, GNSS).
Keep short paths to their exits; do not meander.
- Separation: keep noisy power/switching harnesses ≥ 100 mm from low-level signals; when crossing, do it at 90°.
- Pairing: run supply with its return (twisted if possible) to shrink loop area.
- Chassis-hugging: clamp long runs along metal rails (24.1) to reduce radiation and pickup.
- Ferrites: last-resort band-aids; pick cores sized for the cable and place right at the entry/exit to choke common-mode.
- Antenna keepouts: keep digital and power wiring away from RF modules/antennas; avoid routing behind antenna ground cuts.
3.3.6 Interface panels & filters (stop noise at the wall)
- Feedthroughs / filtered connectors: use at the bulkhead for nasty lines (PWM, long I/O).
- Common-mode chokes on I/O just inside the entry; tie the choke’s shield/can to chassis nearby.
- RC/TVS right at the connector where ESD enters; shortest leads to chassis.
3.3.7 Inside the enclosure (bonds that actually work)
- Paint scrape pads under every intended bond (23.1).
- Board-to-chassis bonds: short, wide straps or mounting posts near the I/O shield.
- Lid seams: conductive gasket or fingers around the perimeter, even compression (23.5).
3.3.8 Quick verification & pre-compliance sanity
- Bond resistance: seam/strap/chassis points < 0.1 Ω (low-ohm meter).
- Shield continuity: shell ↔ shell and braid ↔ chassis low ohms.
- Near-field sniff: handheld probe (or small loop) over hot zones—compare “clamp on/off”, “ferrite in/out” deltas.
- Common-mode current clamp: on external cables during function—look for drops after 360° bonds/ferrites.
- Functional abuse test: toggle relays/PWM while watching radios/GNSS/analog noise; verify no resets or data errors.
3.3.9 Acceptance cues (fast eyes)
3.3.10 Common traps → smallest reliable fix
3.3.11 Pocket checklists
Before build
- Ground strategy chosen (single- vs multi-point) and drawn
- Bond pads exposed; Ω meter at station; star washers in kit
- Shield hardware (360° clamps/backshells) present; ferrites (if any) sized
During routing
- Noisy runs segregated; crosses at 90°; power paired with return
- Shields bonded at entry; pigtails ≤ 10 mm (only if spec’d)
- Gaskets seated; seam compression even; lid bonds in place
Quick verify
- Chassis bonds < 0.1 Ω logged (tray, lid, straps)
- Sniff/common-mode check shows improvement vs open case
- Radios/GNSS/analog behave while PWM/relays chatter